Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAprilaire Duct Repair & Sealing in Spring: What to Know First
We provide independent Aprilaire duct repair and sealing in Spring, TX, with most jobs completed in a single visit and a written price delivered before any work begins. A typical Aprilaire duct sealing job runs $450-$850 for a standard single-system home, while flex duct repair or metal ductwork restoration on Aprilaire-integrated systems ranges $280-$620 depending on accessibility and material. This page is for homeowners in Spring, Gleannloch Farms, and nearby who own an Aprilaire whole-home dehumidifier, ventilation controller, or air cleaner and need the ductwork that connects to it actually fixed, not just vacuumed. Call (346) 423-3631 for a free written estimate.
How Aprilaire Products Fail - and How We Fix Them
- Model 1820/1830 dehumidifier supply duct collapse in Spring’s clay-heavy crawlspaces. The flexible insulated duct between the dehumidifier and main trunk sags where humidity stays high and clay soil shifts the foundation slightly seasonally. We’ve replaced dozens of these in Spring homes near Gleannloch Farms with reinforced flex duct supported every four feet, then sealed with mastic at the collar connection so the dehumidifier’s static pressure doesn’t reopen the leak.
- Model 8126X ventilator backdraft damper seal failure. The foam gasket on the ventilator’s damper housing hardens after 6-10 years in Houston’s heat and UV exposure through attic vents. We remove the Aprilaire unit, fabricate a new gasket from closed-cell neoprene rated for 180°F continuous, and reseal the housing to the duct boot with mastic and fiberglass mesh. OEM gaskets are available but often back-ordered; our neoprene spec outlasts them in field conditions.
- Model 5000 air cleaner duct retrofit gaps from non-standard collar sizing. The 5000 series uses a 20×25 cabinet that doesn’t always marry cleanly to existing return plenums, especially in 2015-2020 Spring builds where builders used knockdown plenum kits. We fabricate transition collars from 26-gauge galvanized or match the existing duct material, seal with mastic, and photograph the joint before the cabinet goes back on.
- Model 600 humidifier bypass duct air leaks at the 6-inch round takeoff. The sheet metal bypass duct on Aprilaire humidifiers vibrates loose where it tees into the supply plenum, particularly on Carrier and Trane systems where the plenum wall is thinner gauge. We cut back to solid metal, install a proper start collar with a draw band, and seal with mastic instead of foil tape, which degrades in attic heat within two years.
- Model 8910 home automation controller duct sensor drift causing false high-static readings. The differential pressure sensor tubing connects to the ductwork with barbed fittings that crack from thermal cycling in unconditioned Spring attics. We replace the tubing with UV-rated polyethylene, verify the sensor calibration against a digital manometer, and seal the penetration with mastic to prevent attic air infiltration that throws off the reading.
Our Aprilaire Duct Repair & Sealing Process
- 1
Camera inspection before quote. We run a borescope through every accessible duct run connected to the Aprilaire equipment and show the homeowner what we found. The camera doesn’t negotiate.
- 2
Written scope and price. We deliver a single-page scope with line-item pricing under Haven Standard Clause 1: one flat price per system, no per-vent add-ons, signed before work starts.
- 3
Parts decision: OEM or verified aftermarket. For Aprilaire-specific collars, dampers, and gaskets, we quote OEM first. If lead time exceeds five business days, we specify the aftermarket equivalent by manufacturer and rating so the homeowner can verify it independently.
- 4
Repair and seal. We match the existing duct construction, fabricate transitions as needed, support flex duct to prevent sag, and seal all joints with mastic and fiberglass mesh. Metal repairs get rivets or draw bands, not screws that loosen from vibration.
- 5
Pressure test and photo record. We verify static pressure at the Aprilaire unit against manufacturer spec, then photograph every sealed joint and repaired run. The photo record is delivered as a standard job deliverable.
- 6
365-Day Done Right Promise in writing. The warranty document is signed by the technician and left with the homeowner before we pack up.
BeforeAfterWhat Aprilaire Duct Repair & Sealing Costs in Spring
| Job Type | Typical Range | What Moves the Price |
|---|---|---|
| Aprilaire bypass duct reseal (Model 600/700 series) | $280-$420 | Attic accessibility, plenum material gauge |
| Flex duct replacement, dehumidifier supply (Model 1820/1830) | $340-$580 | Length of run, need for new supports |
| Ventilator housing reseal with damper gasket (Model 8126X) | $380-$620 | OEM vs. aftermarket gasket, attic temperature conditions |
| Full duct sealing, Aprilaire-integrated system | $450-$850 | System size, number of branch ducts, existing sealant condition |
| Metal duct repair with transition fabrication (Model 5000 retrofits) | $480-$720 | Custom fabrication time, material type |
Every estimate is free and written. We also provide a Free Second Opinion on any competitor’s written estimate, no charge. Call (346) 423-3631 to schedule.
Why Spring Homeowners Call CleanRun Air Duct Cleaning Spring for Aprilaire Work
We’ve worked on Aprilaire equipment in Spring since 2013, including a lot of calls out near Gleannloch Farms where the older construction and clay-heavy soil push debris into return plenums over time. Tomas Reyes, our owner, pulls camera footage before quoting anything because he’d rather show what’s in the duct than describe it. Every crew is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier systems, so when an Aprilaire unit is integrated with another brand’s air handler, we don’t need a second contractor. The 365-Day Done Right Promise is backed in writing on every job, and the photo record is included as standard, not an upsell.
FAQs
No, independent duct repair does not void the Aprilaire product warranty as long as the work is performed on the ductwork itself and not on the Aprilaire unit’s internal components. We are an independent Aprilaire service provider, not authorized by Aprilaire, and we document every seal and connection so warranty claims on the unit remain clean if needed later. If your Aprilaire equipment is still under manufacturer warranty, we note the serial number and install date before starting work so nothing we do complicates a future claim. Call (346) 423-3631 if you want us to verify your warranty status first.
OEM gaskets, dampers, and collars typically ship in 3-5 business days, but Aprilaire’s humidifier and ventilator components have run longer lead times since 2022, sometimes 10-14 days for specialized damper assemblies. We stock quality aftermarket equivalents rated for the same temperature and pressure specs, and we tell you the manufacturer and part number before substituting so you can verify it yourself. If you prefer to wait for OEM, we schedule the job for when parts arrive and lock the written price under Haven Standard Clause 1. Call (346) 423-3631 to check current availability.
Replace the ductwork if more than 30% of the total system length shows degradation, if the original flex duct is pre-2006 and uninsulated, or if repeated repairs in the same zone indicate systemic undersizing. Repair is the better value for isolated leaks, single failed joints, or localized damage from pest intrusion or remodeling. We give an honest assessment with photos of every run so you can see the difference between one bad section and a system at end of life. Call (346) 423-3631 for a free evaluation.
You receive a Documented Photo Record of every duct run, before and after, showing the mastic application, the supported flex, or the fabricated transition. We also take a static pressure reading at the Aprilaire unit and record it on the job ticket. If the numbers don’t match what Aprilaire specifies for your model, we find out why before we leave. This practice has been standard on every CleanRun job since 2013. Call (346) 423-3631 if you want to see sample documentation before booking.
Yes. We regularly service Aprilaire humidifiers, ventilators, and air cleaners integrated with all three brands, and our technicians carry the common transition fittings and collar sizes for each. The duct repair spec changes slightly by air handler manufacturer, thinner plenum walls on some Carrier lines need different support strategies, and we account for that in the written scope. We name the equipment brands we use, Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, and Guardsman, so you can verify our tools independently. Call (346) 423-3631 to schedule.
Ready for a written estimate? Call (346) 423-3631 or schedule online. Every estimate is free, every price is written before work starts, and every job ends with a photo record and a signed 365-Day Done Right Promise.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Spring at CleanRun Air Duct Cleaning Spring, serving Spring and nearby areas.