Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Spring: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Spring, TX, with most residential jobs completed in a single scheduled visit and a written price delivered before any panel comes off. Our typical range for Abatement Technologies evaporator coil and blower cleaning runs $340-$580 for a complete air handler service, depending on access and contamination level. As an independent Abatement Technologies service provider, we are not affiliated with or authorized by the manufacturer, but our technicians are trained on their equipment and carry the right tools to service it without voiding your warranty. If you own an Abatement Technologies air filtration or HVAC unit and need cleaning, call us at (346) 423-3631 for a free estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 750 Series - Blower wheel imbalance from debris caking. The high-static design on these units pulls more particulate through the return than standard residential systems. In Spring, where clay-heavy soil and seasonal pollen create a fine grit, we’ve found blower wheels on the 750 series coated to the point of vibration. We remove the wheel, clean it on a bench with a non-corrosive foaming agent, and rebalance before reinstalling.
- PREDATOR 800 Series - Evaporator coil fin corrosion from condensation trapping. The 800 series uses a tighter fin pitch that holds moisture longer in humid climates. Around Gleannloch Farms and other Spring neighborhoods with older construction, we’ve pulled coils showing early-stage corrosion where the condensate pan drains slowly. We clean with a low-pressure foaming treatment, verify drain slope, and treat the coil with a manufacturer-compatible corrosion inhibitor.
- HEPA-AIRE SAH Series - Filter bypass due to frame seal degradation. The SAH portable units see heavy use in renovation and remediation settings. The filter frame seals compress over time, allowing dirty air to bypass the HEPA media. We disassemble the filter chamber, replace the gasket material with OEM-spec silicone, and pressure-test the seal before return.
- ABATEMENT PAS2400 - Blower motor bearing contamination. This negative-air machine runs long hours on job sites. Bearing grease breaks down when fine drywall dust infiltrates the motor housing. We pull the motor, clean the bearing races with solvent, repack with high-temp grease, and verify amp draw against the nameplate.
- ABATEMENT BD2KL - Heat exchanger soot buildup from incomplete combustion. The BD2KL’s compact firebox can accumulate carbon if gas pressure drifts low. We scope the exchanger with a borescope, media-blast the soot with walnut shell (no wire brushing that damages the aluminized steel), and combustion-test to OEM spec before signing off.
Our Abatement Technologies HVAC Cleaning Process
- 1
Camera inspection before quote. Tomas Reyes pulls a borescope through the plenum (the main distribution box) and into each duct run to show you what’s actually inside. The camera doesn’t negotiate - what we see is what we quote.
- 2
Written price under Haven Standard Clause 1. We deliver a single flat price for the complete system, no per-vent add-ons, before any work starts. You sign it or you don’t. No pressure either way.
- 3
OEM or quality aftermarket parts decision. For Abatement Technologies units, we stock common wear items and source OEM when the warranty is active. Out of warranty, we may recommend quality aftermarket equivalents from Guardsman or Honeywell - always named in writing with the price difference shown.
- 4
Negative-pressure extraction and component cleaning. We seal the system, apply negative-pressure extraction (suction that contains debris rather than blowing it into your home), and clean each component with tools matched to the material - foaming cleaner for coils, mechanical brushing for blower wheels, media blasting for heat exchangers.
- 5
Post-clean photo record and test. Every duct run is photographed after cleaning. We measure static pressure, verify temperature split, and run the system through a full cycle. The photo record and test results are yours to keep.
- 6
365-Day Done Right Promise in writing. If the work is not right, we make it right. The guarantee is printed, signed, and attached to your job record - not a web page policy, a physical document.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Spring
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (single system) | $280-$420 | Access panel location, fin corrosion level, refrigerant handling required |
| Blower wheel and housing cleaning | $180-$290 | Wheel removal difficulty, motor bearing condition |
| Complete air handler service (coil + blower + housing) | $340-$580 | System size, contamination level, parts replacement |
| Condenser coil cleaning (outdoor unit) | $160-$240 | Fins per inch count, fin straightening needed, refrigerant line length |
| Heat exchanger cleaning and combustion test | $320-$480 | Soot depth, media blasting rounds, gas valve adjustment |
Spring’s pollen seasons - oak in March, ragweed in September - push more debris through Abatement Technologies high-static units, which can add 15-20% to cleaning time if the system hasn’t been serviced in two-plus years. We do not quote per-vent or over the phone without seeing the system. Call (346) 423-3631 for a free estimate - we’ll show you the camera footage and the written price before you decide.
Why Spring Homeowners Call CleanRun Air Duct Cleaning Spring for Abatement Technologies Work
We’ve logged a lot of hours in Spring, including plenty of calls out near Gleannloch Farms where the older construction and clay-heavy soil tend to push a surprising amount of debris into return air plenums over time. Our crew knows the difference between a PREDATOR 750 and an 800 series without checking the manual, and we carry the right foaming agents and fin combs for Abatement Technologies’ tighter coil pitches. If your system is down hard, we also service Lennox, Trane, and Carrier - so we’re not guessing when cross-brand compatibility questions come up. Every technician is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. The 365-Day Done Right Promise applies to every Abatement Technologies job we touch, and the photo record is included, not an upsell.
FAQs
No, if the work is performed by a qualified technician using manufacturer-compatible methods and materials. As an independent Abatement Technologies service provider, we document every step - cleaning agents used, pressure readings, before-and-after photos - so you have a record if a warranty question ever arises. We do not use wire brushes on aluminized heat exchangers or high-pressure water on electrical components, both of which can void coverage. Call (346) 423-3631 if you need documentation for a warranty claim.
You receive a Documented Photo Record of every duct run and component, before and after, as a standard deliverable on every job. We started this practice in 2013 and have held to it on all 52,000-plus homes we’ve served. The photos are time-stamped and delivered with your written invoice. If a company won’t show you the inside of your own ducts, they didn’t clean them.
Replace if the heat exchanger is cracked, the compressor has failed under warranty twice, or repair costs exceed 40% of replacement value on a unit over 12 years old. Clean and repair if the issue is contamination-related - dirty coils, blower imbalance, or control board failure from dust infiltration. We offer a Free Second Opinion on any written estimate; bring us a competitor’s replacement quote and we’ll put our repair number next to it in writing.
Most residential jobs run 3-5 hours for a complete air handler service. A single evaporator coil or blower cleaning takes 1.5-2.5 hours. We schedule a window, not a rush, because proper negative-pressure extraction and photo documentation can’t be shortcut. Call (346) 423-3631 to book - estimates are free and include the camera inspection.
We stock common wear items for PREDATOR and HEPA-AIRE series units, and we source OEM parts within 24-48 hours for most discontinued models. For the BD2KL and older PAS series, some components are rebuild-only - blower motors rewound, heat exchangers media-blasted rather than replaced. We tell you which path we’re taking and why, in writing, before work starts.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Spring at CleanRun Air Duct Cleaning Spring, serving Spring and nearby areas.